芯片型号：CP1154

• The CP1154 is one of the OPTRANS series chips designed by Chiphomer Technology Limited. It is a highly integrated EOS device that provides for mapping of 10/100/1000 Mbit/s Ethernet into SDH STM-1 Transport payloads. The device supports connection for up to four 10/100 Mbit/s Ethernet ports, using SMII or SS-SMII interface, or one 1000 Mbit/s Ethernet port, using GMII interface. Ethernet frames are encapsulated using either GFP or HDLC-like protocol. The encapsulated Ethernet frames are then mapped into virtually concatenated VC-12, VC-3 or VC-4 payloads. Link Capacity Adjustment Scheme (LCAS) for VC-12/VC-3/VC-4 virtual concatenation is provided to enable hitless addition and removal of bandwidth under the control of a network management system. The VC-12, VC-3 and VC-4 POH generation and termination are performed. A byte-wide 19.44MHz Telecom Bus interface is provided for the SDH interface.

• Supports up to four ports of full-duplex10/100 Mbit/s Ethernet or a single port of full-duplex 1000 Mbit/s Ethernet with standards-compliant flow control supported:

▋10/100 Mbit/s Ethernet interface supports SMII and SS-SMII

▋1000 Mbit/s Ethernet interface supports GMII

• Ethernet Management interface (MDIO) for control and configuration of external connected PHYs

• Provides IEEE 802.3 Management Statistics (RMON)

• Supports multiple virtual concatenation groups from one Ethernet port based on VLAN tag identification

• Supports multiple virtual concatenation groups to one Ethernet port based on the user’s configuration

• Supports up to 16 virtual concatenation groups

• Supports up to four priority queues, enabling time-sensitive data to have access to the network with

minimal delay

• Provides RED algorithm for buffer management

• Provides per-priority scheduling using Round Robin mechanism

• Supports the following encapsulation/decapsulation protocols on a per port basis:

▋ITU-T G.7041, Generic Framing Procedure (GFP)

▋HDLC-like Framing, including the following protocols:

▋ITU-T X.86/X.85, Link Access Procedure SDH (LAPS)

▋RFC1662, Point-to-Point Protocol (PPP)

• RFC3518, PPP Bridging Control Protocol (BCP)

• Supports the following SDH mapping formats:

▋C-12/VC-12/TU-12/TUG-2/TUG-3/VC-4/AU-4/STM-1

▋C-3/VC-3/TU-3/TUG-3/VC-4/AU-4/STM-1

▋C-4/VC-4/AU-4/STM-1

• Supports selection of VC-4, VC-3 or VC-12 virtual concatenation on a per virtual concatenation group basis

• Supports hitless Link Capacity Adjustment Scheme (LCAS) (ITU-T G.7042)

• Supports up to 240ms (VC-12)/254ms (VC-3) of differential delay

• Supports TU-12/TU-3 pointer interpretation

• Supports VC-12, VC-3 and VC-4 POH generation and termination

• Full access VC-12, VC-3 and VC-4 POH through external serial interface

• Provides byte-wide 19.44MHz Telecom Bus interface

• Controlled High-Z output on Output Telecom Bus

• Provides three bus timing modes for Output Telecom Bus

• Supports per-port Ethernet side and SDH system side loopbacks for system level diagnostics

• Provides 16-bit Intel/Motorola microprocessor interface

• Provides an IEEE 1149.1 compliant JTAG test port for boundary scan

• Operating Industrial temperature range: -40℃—85℃

• Low power 1.8V core with 3.3V LVTTL I/O, LVPECL I/O and 2.5V SSTL_2 digital I/O

• The maximum power consumption is 2.1W

• 27x27mm PBGA 352 package

SDH Add/Drop Multiplexers、SDH Terminal Multiplexers、Multi-service Access Platform (MSAP) 、Customer Premises Equipment (CPE) platform、Test Equipment